|Accordia-Fold is a trademark name for the accordion style pleating of drapery. Unlike Ripple-Fold, the spacing of the fabric is a direct result of the sewn in pleats which are sharp and crisp compared to any other style of drapery. Used primarily in Healthcare applications,|
Accordia-Fold draperies stack tighter when open but tend to leak light at the edges so are not the best choice for full blackout applications. Additionally, due to the way they hang below the track, a full top treatment is required if complete room darkening is desired. A main advantage of Accordia-Fold draperies is their ability to break-away from the tracking system much easier than a standard pin or grommet hung drapery system, making this style of drapery a preferred choice for mental health and rehabilitation facilities.
Straight needled with nylon snap tape. Fullness determined by snap tape and pleat depth. Specify 220%, 200%, 180% or 160%.
Standard: Face fabric is double turned at top. Note: Face fabric is exposed at back top of drapery for 4”.
Custom: Lining should be extended to the top of the drapery before folding over the buckram.
2-Pass Blackout: Flame retardant 2-pass blackout lining with foam on one side and 70% polyester / 30% cotton on the other side. White or Ecru on the foam side and gray on the poly/cotton side.
3-Pass Blackout: Flame retardant 3-pass blackout lining with both foam and 70/30 poly-cotton sides. White or Ecru on the foam side and White on the poly/cotton side. Colors on the face are available. Contact our sales department for more information.
4” Buckram, permanent finish, washable. 5” Buckram on draperies over 108” is optional.
Face: Overlocked using 5 thread safety stitching. All selvages are to be removed and patterns matched on 54” goods. Not less than 1/2 width used per panel unless specified.
Lining: Overlocked using a 5-thread safety stitch.
3-Pass Blackout: Free Standing and French Seamed so as to minimize the appearance of pin holes on the vertical face.
Face: 4” Single or double fold, as specified, with blind stitched hems.
Lining: Overlocked bottom edge of lining. Note on cotton, poly/ cotton, cotton/rayon, etc. Lining will be a minimum of 1 1/2” up from bottom of drapery.
1.5” double turned
Square covered weight sewn on each seam and corner of face fabric.
Standard 3 1/2”, 6” for double rod treatments and 9” for 3-rod system.
Sew closures at bottom hems using a Bonis Brothers Sewing Machine.
Drapery to be fan folded, packed in poly bag and boxed. The drapery will be labeled with area and/or room number. Drapery “dressing” is part of installation. Creasing during shipping is unavoidable. Steaming may be required. Proper installation requires breaking of the buckram in between each pleat.
Snap tape spaced at 4.25” on center is standard.
Standard 4” double turned top and bottom. On ceiling to floor lengths, seamless 118” sheer is recommended. There is a maximum finished length of 100” when using 118” sheer. 6 pleats per 60” fabric width. Covered weights at side hems and seams are standard.
Optional: Continuous covered weight for 118” sheers.
Note!!! Drapery sizes may vary +/- 1/2” in length.
Brochure - Accordia Fold Drapery
Accorida Fold Drapery brochure containing styles, options, fabrication methods, care recommendations, and specifications.
Updated: Friday, May 12, 2017 @ 07:21 AM
Care Instructions - Drapery Fabric
Complete Drapery Fabric care instructions containing recommended washing, drying, and finishing details.
Updated: Thursday, May 11, 2017 @ 02:44 PM
Specifications - Accordia Fold Drapery
Full Architectural Specification sheets detailing product options, details, and supplier duties. Also available in DOC (Word) format.
Updated: Friday, May 12, 2017 @ 07:40 AM
Specifications - Accordia Fold Drapery
Full Architectural Specification sheets detailing product options, details, and supplier duties.
Updated: Friday, May 12, 2017 @ 07:48 AM